平衡调温调湿方式中变流量冷冻水系统设计

通过对变流量冷冻水系统的分析指出，在运用平衡调温调湿方式的空调系统中，应用变流量冷冻水系统可以较大地节约能源和投资；并提出了实现这种应用的方法。     

基于超低电容特性的微尘在线监测技术研究

为了更有效地测量工业烟尘排放浓度,研究了一种电容特性的微尘在线监测技术,利用电容传感器输出电压来反映粉尘质量。介绍了电容法测量粉尘量的原理、测量系统组成等,研究了粉尘质量与电容传感器输出电压的关系。对5种不同粉尘的测量结果进行分析表明,粉尘质量与电容传感器输出电压之间存在着一定的比例关系,其相关系数高达0.99。同时进行了微尘在线测量的研究,并采用电容特性曲线对测量系统进行了标定,从而验证了电容法在线微尘监测的可行性。     

Toluene decomposition performance and NOx by-product formation during a DBD-catalyst process

Characteristics of toluene decomposition and formation of nitrogen oxide (NOx) by-products were investigated in a dielectric barrier discharge (DBD) reactor with/without catalyst at room temperature and atmospheric pressure. Four kinds of metal oxides, i.e., manganese oxide (MnOx), iron oxide (FeOx), cobalt oxide (CoOx) and copper oxide (CuO), supported on Al₂O₃/nickel foam, were used as catalysts. It was found that introducing catalysts could improve toluene removal efficiency, promote decomposition of by-product ozone and enhance CO₂ selectivity. In addition, NOx was suppressed with the decrease of specific energy density (SED) and the increase of humidity, gas flow rate and toluene concentration, or catalyst introduction. Among the four kinds of catalysts, the CuO catalyst showed the best performance in NOx suppression. The MnOx catalyst exhibited the lowest concentration of O₃ and highest CO₂ selectivity but the highest concentration of NOx. A possible pathway for NOx production in DBD was discussed. The contributions of oxygen active species and hydroxyl radicals are dominant in NOx suppression.     

雾化介质阻挡放电联合电晕放电对染料溶液脱色研究

实验将介质阻挡放电与电晕放电组合在一个反应器内,以靛蓝二磺酸钠溶液为实验废水,将高压电极上通入50Hz交流高压电,在常压空气中形成介质阻挡放电-电晕放电系统,放电产生的低温等离子体及其活性基团作用于染料分子。考察了电源电压、电极间距、处理时间对染料溶液脱色率和能量效率水平的影响,确定反应器工作状态为介质阻挡放电系统电极间距30mm、电晕放电系统电极间距25mm、电源电压20kV。     

圆管空拔壁厚变化分析

此文利用主应力法推导出圆管空拔壁厚变化量解析式。该式计算结果与以定常三维流动上界解析同类问题结果相接近,且表达式简单,也与拔管的实验结果相一致。因而,可在圆管空拔壁厚计算时推广应用。     

Chemical dechlorination of polychlorinated biphenyls (PCBs) from dielectric oils

We studied the chemical dechlorination of the polychlorinated biphenyls (PCBs) in some dielectric oils via nucleophilic substitution of the chloro atoms by polyethylene alkoxide. The influence of temperature, ultrasounds, polyethylene glycol (PEG) and base type was investigated. Our findings show that dechlorination of PCBs by chemical treatment is effective at moderate temperature (90–100°C) and is strongly dependent on the nature of matrix oil. Stirring affects the process yield by influencing the homogeneity of the oil/glycol two-phase system. Ultrasounds can improve the process efficiency by making operating conditions less severe. Selected article from the 6th European Meeting on Environmental Chemistry, University of Belgrade, Serbia and Montenegro organized by Prof. Dr. Branimir Jovancicevic ().     

Determination of levels of polychlorinated biphenyl in transformers oil from some selected transformers in parts of the Greater Accra Region of Ghana

Although polychlorinated biphenyls have never been manufactured in Ghana, it has been used extensively as dielectric fluid in electric transformers and capacitors. However, very little is known of its health and environmental impacts by both managers of these transformers and capacitors and also the general public. This work therefore seeks to explore INAA as a possible alternative to screening transformer oils for PCBs by determining the total chlorine content. The total chlorine content of transformer oil samples from Ghana that tested positive and some randomly selected samples that tested negative from screening using CLOR-N-OIL test kits, have had their total chlorine estimated. INAA using the Research Reactor located at the Ghana Atomic Energy Commission was used to estimate the total chlorine content of the oil samples. Neutron Activation and gamma ray spectroscopy using HPGe detector coupled to MAESTRO 32 software was used to determine the total chlorine content by integrating the peak area of the spectrum into a simplified program that was developed from the activation equation. Instrumental Neutron Activation Analysis was able to validate the result obtained from the test kits screening with accuracy 7.5%.The minimum total chlorine content of the positive samples determined by NAA was 71.34 μg g⁻¹.     

Toluene decomposition performance and NOx by-product formation during a DBD-catalyst process

Characteristics of toluene decomposition and formation of nitrogen oxide (NO_x) by-products were investigated in a dielectric barrier discharge (DBD) reactor with/without catalyst at room temperature and atmospheric pressure. Four kinds of metal oxides, i.e., manganese oxide (MnOx), iron oxide (FeOx), cobalt oxide (CoOx) and copper oxide (CuO), supported on Al₂O₃/nickel foam, were used as catalysts. It was found that introducing catalysts could improve toluene removal efficiency, promote decomposition of by-product ozone and enhance CO₂ selectivity. In addition,NO_xwas suppressedwith the decrease of specific energy density (SED) and the increase of humidity, gas flow rate and toluene concentration, or catalyst introduction. Among the four kinds of catalysts, the CuO catalyst showed the best performance in NO_x suppression. The MnOx catalyst exhibited the lowest concentration of O₃ and highest CO₂ selectivity but the highest concentration of NOx. A possible pathway for NOx production in DBD was discussed. The contributions of oxygen active species and hydroxyl radicals are dominant in NOx suppression.     

提高测量悬浮物的准确性

通过一系列实验数据的对比，提出影响悬浮物测量准确性的两个因素——空气相对湿度和称量时间控制，从而提出较为可行的测量方法与步骤．